Welcome to Gearstar Performance

Gearstar installs automatic 3 speed and 4 speed transmissions in any car or truck

Gearstar installs automatic 3 speed and 4 speed transmissions in any car or truck

Doug disassembling transmission and inspection of components

Trans cases being prepped and to be painted for assembly

Vintage transmission parts ready for assembly

Prepped transmission cases ready for remanufacturing

Patrick: Preparing to wash a transmission case in our state of the art parts washer

Overview of Gearstar production area

Photo of some Gearstar technicians

Thomas finishing a transmission

Transmission sub-assemly being checked at builders bench

Final assembly of 4L80E

Reinstalling transmission pan after final calibration.

700 R4 transmission and valve body assembly

Final assembly for a 200 4R transmission

Complete pump assembly being installed in a 4L60E

This is a 3-4 high capacity clutch assembly being installed into a 4L60 level IV transmission clutch drum.

This C5R 444 LSX engine in our 2000 Camaro Shop Car built by Wheel to Wheel, puts out a whopping 870 hp at the rear wheels. The

Patrick is installing a new governor cover on a 4L60 level IV transmission.

Patrick is getting ready to install a 4th gear super hold servo on a 4L60 level IV transmission. This increases the 4th gear by

Patrick putting the tail housing on a 700 R4 transmission.

Patrick assembling the input drum on a 545RFE.

Patrick inspecting the 545RFE over drive clutch assembly before installation.

He then installs the 545RFE input drum assembly into the transmission case.

Then he installs the completed 545RFE front pump assembly into the case.

Patrick is preparing to torque the valve body bolts on the 545RFE.

Mark is removing old bushings on a 350 transmission to be replaced.

He then installs new bushing sin the mechanical press.

He then installs new bushings in the mechanical press.

Mark, our master tech, is installing the completed rear planetary and output shaft assembly into the transmission case.

He then proceeds to install the high capacity clutch drum pistons into each drum set.

He then installs the clutches and steel plates into the drum sets.

Patrick is installing one of our deep cast aluminum pans on one of our level IV 400 transmissions.

Master Tech Steve is installing a chrome pan on a level II 350 transmission.

Tom is preparing to tighten the control valve body bolts on a 4L60 level II transmission.

Steve is applying a sealer to a rear seal to be installed in a 350 tail housing.

Steve is applying a sealer to a rear seal to be installed in a 350 tail housing.

Thomas inspects the valve movement ina 4L60 valve body he finished assembling. We double check every aspect of our assembly pro

Mark, general manager & master technician, assembling the clutch drum on a TH 350

Patrick is preparing to install a Gearstar re-programmed valve body

Installing adapter plate assembly for proper fit

200 4R after assembly - ready for Dyno test

A finished Gearstar performance turbo 350 Level IV with 11" full billet racing converter

Zack standing next to 4L85E transmission with custom Hemmy billet aluminum adapter

Gearstar transmission being tested on Dyno before shipping

Transmission being prepared for Dyno testing

Calibration being checked on 700 R4/4L60 transmission while on Dyno

Mark our master technician performing a valve body calibration during Dyno testing

Finished Gearstar Performance transmissions

4L80E Level IV transmission with billet racing converter after final Dyno test

Tony is ready to install a high stall, furnace brazed with flanged hub torque converter into is completed 4L60 for dyno testing.

Tony finishes a 200 4R at his bench.

He checks the selector shaft threads on a 200 4R before seeding it to the dynometer.

David is installing a drum assembly on a transmission at his bench.

Zack is at our dynometer pre-filling a torque converter before he installs it into the transmission he's going to test.

Zack installs the rear yoke assembly into a 4L65E before testing. This output shaft and yoke simulate vehicle load and weight.

Patrick and Mark working together on the dynometer to unhook a 4L60 level II transmission. If a builder has a free minute he alw

Thomas checks operating pressures and electronics on his transmission while dyno testing it.

Thomas at this bench with a partially assembled 4L60 level II transmission.

A view of our production area and builders stations.

A view of our production area and builder stations.

Finished Gearstar Performance 700 R4/4L60 Level IV transmission

Gearstar performance state of the art dynometer used for testing "every transmission built"

Zack Dyno testing one of Gearstar's 4L65E Level III transmissions

Thomas Dyno testing his transmission

Mark is getting ready to re-calibrate a transmission on the Dyno

Finished Gearstar 700 R4 Level IV Transmissions

Gearstar finished transmissions - 700 R4 (left), 4L80 (center and right)

Our finished transmissions after Dyno testing waiting to be crated for shipping

Some of the Gearstar crew with our finished product; Pictured from front to back: Zack, Pat, Toni and Mark

Thomas preparing a transmission for shipping

One of Gearstar Performance's transmissions crated and ready for shipping

Gearstars finished transmission shown here in it's integrated wood crate, ready for delivery

Tom placing a Gearstar transmission on trans jack for installation in car

Gearstar installs automatic overdrive transmissions - Pictured: Our Gearstar "White Magic" race car

86' Monte Carlo on lift being fitted with Gearstar 200 4R Level 4 transmission

This 1954 Chevy BelAir has been fitted witha Gearstar Performance 4L60 level B transmission. We custom install our overdrive tr

One of the power plants that Gearstar Performance puts overdrive tranmsission behind. This 572 CI was fitted with a Gearstar 4L8

Flex plate inspection

Gearstar Level II torque converter

4L60 being calibrated further in 1954 Chevy BelAir

4L60 in '34 Ford final inspection after installation

Mark making final adjustments on throttle valve cable on 69' Grand Sport

'66 Chevelle on lift being fitted with Gearstar 200 4R Level 5

Some of the Gearstar team with 2009 Street Rodder Road Tour car

The 2009 Street Rodder Road Tour cars at the Gearstar Road Tour event

2009 Street Rodder Road tour participant's car at Gearstar's Road Tour event

Mark showing the Road Tour group what goes into a Gearstar transmission

Mark explaining how we calibrate our speedometers to your cars specifications and needs

Patrick talking to a Street Rodder Road Tour participant about the best transmission package for his car